Pocket Door Magic – Electrical Switches And Outlets Near The Door
Yes, I believe I’ve now earned the right to write a "how to" post on pocket door installation. One install and you know it all. Er, maybe not. But here is what I learned, in case you want to tackle one! pocket doors ukIf you have found the most perfect flush pulls for your bedroom or bathroom door you can add pocket door jamb bolts for privacy locking. The jamb bolt is installed on the inside of the pocket door and operates like a rocker switch, physically preventing the door from returning to the pocket. There is a strike plate included that attaches to the door jamb to protect it from damage, as well as trim for an emergency release hole for outside the door in case someone accidentally gets locked inside.
This is a handy device for use as a privacy lock on pocket or sliding doors that do not have a lock installed. This pocket door jamb bolt is designed to be face mounted at the rear of a closed pocket door, acts as a privacy bolt to prevent door from opening. It works like a rocker switch. When pushed in, the other half pops out, physically preventing the door from returning into its pocket. For emergency access a small hole can be drilled through the door and a slim object can be inserted through the hole to flip the rocker closed. Made of solid brass and available in 7 popular finishes.
new door installation
Sometimes the trim moulding is installed very close to the door. This gives you a very clean look, but it doesn’t allow much space for the pocket door pulls to clear the trim moulding when sliding the door in and out of the wall pocket. Most pocket door pulls will only require 3/32" clearance on both side of the door, however some will require 1/8" or more on both sides. Check the hardware’s specified projection (how far it sticks off the door’s face) to insure it can clear any existing trim mouldings
Once the frame is installed you drywall over the frame. Make sure you use short screws so that the screws don’t penetrate the frame and create a barrier for the door to slide. Next you’ll want to trim the door opening. You’ll need to install a narrow piece of jamb trim on each side of the door and also on the top (see the photo below). One of the pieces of jamb trim on the top will need to be easy to remove. If your door comes off the track the only way to re-install the door is to remove the trim so you can lift the door back on the track. If you notice in the photo we used some trim screws to attach one piece of the upper jamb trim.
install a door
Installing Pocket Door
One way to gain extra usable space in a room is to install a pocket door. A pocket door does not use the room a standard door needs to swing out, so it provides an average of an extra ten feet of usable floor space. Here is how to install a single pocket door. double pocket door hardwareIf you choose to paint the door while it’s in the pocket, be sure to paint both sides of the door, especially if it’s got a hollow core. If you paint only one side, the moisture alone will warp the door. Cut out for the handle before you paint; you may find it easier to make this cut with the door lying between sawhorses. One last point—install adhesive on the bottom of the pocket frame where it rests on the floor (this, of course, depends on the frame’s structure). A strong bond to the floor will help stop the pocket from movement.
Reinforce the pocket structure by installing two sets of pocket door "stiffeners" (thin metal supports supplied with the kit). One set, called jamb stiffeners, is first attached to the header, plumbed up and then fastened to the floor. Another pair of stiffeners is positioned and attached in the middle of the pocket framing. The instructions that come with your pocket door kit will explain precisely where these stiffeners, called side-split jambs, need to be installed.
buy pocket doors
The most important thing is to realize what the pocket door may be sharing with the standing wall. It’s possible that the wall on either side of the framing as well as above the door will enclose electrical lines, air ducts, and plumbing. With new construction or larger remodeling projects , this may not be an issue, as you can flush this out ahead of time on your own or with the help of a remodeling contractor But with an existing wall, don’t swing a single sledgehammer before determining if these elements exist and if they can be relocated. Once that’s complete, you will need to do some deconstruction prior to installing a pocket door to adjust the door frame and jamb. Steps for Installation bathroom glass door
Pocket doors are special types of doors that slide inside a space or compartment when opened. It gives people the illusion that it is not there to begin with making it very popular amongst homeowners who want to save space. It was designed more than a decade ago for this purpose, but it was during the Victorian period when it became a favorite. It was mainly utilized for the library, dining area, or sitting room. Its popularity continued until it completely dropped out from the consciousness of house owners and architects. The comeback of pocket doors.
Installing Pocket Door
where to buy a pocket door install a sliding door
One way to gain extra usable space in a room is to install a pocket door. A pocket door does not use the room a standard door needs to swing out, so it provides an average of an extra ten feet of usable floor space. Here is how to install a single pocket door.
If you choose to paint the door while it’s in the pocket, be sure to paint both sides of the door, especially if it’s got a hollow core. If you paint only one side, the moisture alone will warp the door. Cut out for the handle before you paint; you may find it easier to make this cut with the door lying between sawhorses. One last point—install adhesive on the bottom of the pocket frame where it rests on the floor (this, of course, depends on the frame’s structure). A strong bond to the floor will help stop the pocket from movement.
pocket door price
Reinforce the pocket structure by installing two sets of pocket door "stiffeners" (thin metal supports supplied with the kit). One set, called jamb stiffeners, is first attached to the header, plumbed up and then fastened to the floor. Another pair of stiffeners is positioned and attached in the middle of the pocket framing. The instructions that come with your pocket door kit will explain precisely where these stiffeners, called side-split jambs, need to be installed.
The most important thing is to realize what the pocket door may be sharing with the standing wall. It’s possible that the wall on either side of the framing as well as above the door will enclose electrical lines, air ducts, and plumbing. With new construction or larger remodeling projects , this may not be an issue, as you can flush this out ahead of time on your own or with the help of a remodeling contractor But with an existing wall, don’t swing a single sledgehammer before determining if these elements exist and if they can be relocated. Once that’s complete, you will need to do some deconstruction prior to installing a pocket door to adjust the door frame and jamb. Steps for Installation
Pocket doors are special types of doors that slide inside a space or compartment when opened. It gives people the illusion that it is not there to begin with making it very popular amongst homeowners who want to save space. It was designed more than a decade ago for this purpose, but it was during the Victorian period when it became a favorite. It was mainly utilized for the library, dining area, or sitting room. Its popularity continued until it completely dropped out from the consciousness of house owners and architects. The comeback of pocket doors.
One way to gain extra usable space in a room is to install a pocket door. A pocket door does not use the room a standard door needs to swing out, so it provides an average of an extra ten feet of usable floor space. Here is how to install a single pocket door.If you choose to paint the door while it’s in the pocket, be sure to paint both sides of the door, especially if it’s got a hollow core. If you paint only one side, the moisture alone will warp the door. Cut out for the handle before you paint; you may find it easier to make this cut with the door lying between sawhorses. One last point—install adhesive on the bottom of the pocket frame where it rests on the floor (this, of course, depends on the frame’s structure). A strong bond to the floor will help stop the pocket from movement.
pocket door price
Reinforce the pocket structure by installing two sets of pocket door "stiffeners" (thin metal supports supplied with the kit). One set, called jamb stiffeners, is first attached to the header, plumbed up and then fastened to the floor. Another pair of stiffeners is positioned and attached in the middle of the pocket framing. The instructions that come with your pocket door kit will explain precisely where these stiffeners, called side-split jambs, need to be installed.
The most important thing is to realize what the pocket door may be sharing with the standing wall. It’s possible that the wall on either side of the framing as well as above the door will enclose electrical lines, air ducts, and plumbing. With new construction or larger remodeling projects , this may not be an issue, as you can flush this out ahead of time on your own or with the help of a remodeling contractor But with an existing wall, don’t swing a single sledgehammer before determining if these elements exist and if they can be relocated. Once that’s complete, you will need to do some deconstruction prior to installing a pocket door to adjust the door frame and jamb. Steps for Installation
Pocket doors are special types of doors that slide inside a space or compartment when opened. It gives people the illusion that it is not there to begin with making it very popular amongst homeowners who want to save space. It was designed more than a decade ago for this purpose, but it was during the Victorian period when it became a favorite. It was mainly utilized for the library, dining area, or sitting room. Its popularity continued until it completely dropped out from the consciousness of house owners and architects. The comeback of pocket doors.
Door Installation And Repair Services
The pocket door comes in handy in a tight area where you want a door but cannot fit a swinging door. Installation of a pocket door allows for nearly 10 extra square feet of usable space as compared with a hinged door. A hinged door can be impractical in a small bathroom or a kitchen where it can block a cabinet.a sliding wall and sliding door design and manufacturing company, with over 14 years of experience dedicated to pursuing the art and technology of interior division. Our patented TWINFRAME sliding door design and proprietary no floor track installation are signature features. We specialize in interior dividing solutions with over 13 technically advanced system configurations. Our doors are handcrafted in New York, USA and offer ADA compliant, as well as green options for residential, hospitality and commercial spaces.
Pocket door hardware kits
If the design of your home presents a space where a hinged door would be in the way when left open, it should be considered for a pocket door. Walk-in closets, the door into the toilet/bath area of a bathroom, and walk-in pantries are all great places for pocket doors. Additionally, hinged doors used between rooms and kitchens should be replaced with pocket doors because hinged doors take up valuable wall space if swung into the dining room. They also block counters if swung into the kitchen and they interfere with refrigerators. pocket door for bathroom
Pocket doors are made with various materials. Wood, steel, and glass are the most common ones. The first one is favored for its warm and cheerful vibe, while the steel provides durability and longevity. In the meantime, glass is used for a modern approach. It is sleeker and usually utilized as a room separator without blocking the source of light coming from another area. This allows the homeowners to save on energy cost. Furthermore, when the right pocket door hardware is used, people can close the door securely without even needing a locking mechanism. Categories of pocket door hardware door frame installation
In certain cases, a homeowner will evaluate their floor plan and find great places to replace hinged doors with pocket doors. However, frequently they run into problems when the wall they want to put the pocket door contains a light switch, an outlet, or water pipes (like to a shower head). Special rearranging may need to be made in order to use the pocket door. For example, you may need to put the shower head at the other end of the shower or move the light switch to the other side of the doorway. But believe me, if you can eliminate an inappropriate hinged door, it will definitely be worth it in the end.
sliding bathroom door
How To Install Pocket Door Frames
install entry door
Don’t let your remodeling budget go over-board by hidden surprises – understand what the average Cost to Install a Pocket Door is in your zip code by using our easy to use calculator. If you’re looking for 2013 breakdown Cost to Install a Pocket Door with materials, and how much a contractor might be, you’ve come to the right place.
For privacy locking we also offer double pocket door locks The hardware is the same but the installation is different than for a single pocket door. In this case one door will serve as the active door and will contain the latching mechanism, the other will be the inactive door and will have an edge pull, two flush pulls and the strike plate installed. The active door will have the same lock/latch body as a single door configuration, but instead of installing the strike on the door frame as with a single door, it will be installed on the inactive door so they will latch or lock firmly together in the middle. Since the inactive door has no internal mechanism installed, it does not interfere with the strike.
interior bathroom doors
A pocket door is designed to slide away into the pocket of a wall cavity taking up virtually no wall space and requiring no room to swing out and open like a traditional door. This feature makes a pocket door the ideal choice for entry into a room where space is at a premium but privacy is required. Two pocket doors are often used to create a grand entrance into a dining room or parlor. A pocket door is actually a system that includes hardware and special framing, which is sold separate from the door. The door can be any flat surface or a paneled, hollow or solid door, so it’s style can be matched to other doors in a home.
Our system’s unique design provides the ultimate in versatility in the heavy duty pocket door frame market. We offer an all-inclusive kit for a complete installation by the consumer. Kits are available in all standard sizes and Christner specializes in custom sizes and applications for any width, height, and wall thickness. We manufacture frames for single doors, pairs, and multiple doors stacking in one pocket. We create arches and can provide hardware for surface mount sliding doors.
When purchasing pocket door hardware, homeowners should be well aware of their needs. Some do not include locks because they will just use the pocket door to separate rooms, while others specifically look for privacy. People who belong in the latter must be careful when choosing locking mechanisms that they are going to utilize for their doors. A room that needs latches and locks includes the home office, bathrooms, closets, and storage space. In some cases, homeowners include a release hole outside the pocket door. This is used for emergencies so a person who is locked inside can be easily rescued. Of course this is a good addition that has a lot of benefits, though it is not really required. Common questions about pocket doors
pocket doors repair
pocket door installation, pocket doors installation, pocket doors, door installationhow to install pocket doors
Don’t let your remodeling budget go over-board by hidden surprises – understand what the average Cost to Install a Pocket Door is in your zip code by using our easy to use calculator. If you’re looking for 2013 breakdown Cost to Install a Pocket Door with materials, and how much a contractor might be, you’ve come to the right place.For privacy locking we also offer double pocket door locks The hardware is the same but the installation is different than for a single pocket door. In this case one door will serve as the active door and will contain the latching mechanism, the other will be the inactive door and will have an edge pull, two flush pulls and the strike plate installed. The active door will have the same lock/latch body as a single door configuration, but instead of installing the strike on the door frame as with a single door, it will be installed on the inactive door so they will latch or lock firmly together in the middle. Since the inactive door has no internal mechanism installed, it does not interfere with the strike.
interior bathroom doors
A pocket door is designed to slide away into the pocket of a wall cavity taking up virtually no wall space and requiring no room to swing out and open like a traditional door. This feature makes a pocket door the ideal choice for entry into a room where space is at a premium but privacy is required. Two pocket doors are often used to create a grand entrance into a dining room or parlor. A pocket door is actually a system that includes hardware and special framing, which is sold separate from the door. The door can be any flat surface or a paneled, hollow or solid door, so it’s style can be matched to other doors in a home.
Our system’s unique design provides the ultimate in versatility in the heavy duty pocket door frame market. We offer an all-inclusive kit for a complete installation by the consumer. Kits are available in all standard sizes and Christner specializes in custom sizes and applications for any width, height, and wall thickness. We manufacture frames for single doors, pairs, and multiple doors stacking in one pocket. We create arches and can provide hardware for surface mount sliding doors.
When purchasing pocket door hardware, homeowners should be well aware of their needs. Some do not include locks because they will just use the pocket door to separate rooms, while others specifically look for privacy. People who belong in the latter must be careful when choosing locking mechanisms that they are going to utilize for their doors. A room that needs latches and locks includes the home office, bathrooms, closets, and storage space. In some cases, homeowners include a release hole outside the pocket door. This is used for emergencies so a person who is locked inside can be easily rescued. Of course this is a good addition that has a lot of benefits, though it is not really required. Common questions about pocket doors
pocket doors repair
pocket door installation, pocket doors installation, pocket doors, door installationhow to install pocket doors
How Do I Secure Electrical Wiring To A Pocket Door Frame?
internal door hinges
The prefinished steel P-Series Pocket Door Trim Kit is used to trim out Pocket Door openings. The purpose of the P-Series Pocket Door Trim Kit is to make Pocket Door openings consistent with other Timely Frames on the project.
Once layout is locked down, buy the straightest framing you can find and install it right away. Make sure you’ve read the pocket door hardware manufacturer’s instructions (we used a Johnson Hardware kit for double pocket doors). The manufacturer will provide measurements to get the rough-opening correct. Make sure your wall is straight and plumb, and most of all, that the head jamb is as level as possible—even if the floor isn"t. In fact, the floor in this project changed over an inch in the span of 60 inches. A key control point is clearance under the door. You want at least 3/4 inch for air to flow beneath the door.
best pocket doors
OK, let’s assume that none of those items is there, and you would like to install the door. A 32 inch door requires approximately 66 inches of linear space for the pocket door frame to be installed. The sheet rock will need to be removed, and more often than not, from both sides of the wall. The studs will also have to be removed so that a new door header can be installed. Depending upon the situation metal wrapped split studs may have to be installed to allow the new door to slide back and forth between them. Brackets will have to be installed. converging pocket door hardware
The Johnson Hardware 1500 Series Sliding Pocket Door Frame kit is an easily assembled, structurally strong pocket door frame designed for fast installation in standard 2 x 4 timber or steel-frame stud walls typically sheathed with drywall. Versatile frame can be adapted for use in thicker walls or cut down to accept any smaller size door. Features removable aluminum track with low-friction convex track rails; guaranteed jump-proof, smooth-rolling tricycle hangers; rust-resistant, zinc-plated, steel-reinforced, timber-split studs and self-adjusting floor anchors.
You can attach drywall to the frame, if you"d like, smooth and finish the wall and seams. Never use nails when installing a pocket door, as nails in the wall will impede the door’s flow. If you’ve purchased a door handle and lock for your pocket door, install the lock according to the instructions on the package. If you have an uncut doorframe, you will need to use a chisel to cut a depth for the locking mechanism. Follow the instructions on the package to do so.
The prefinished steel P-Series Pocket Door Trim Kit is used to trim out Pocket Door openings. The purpose of the P-Series Pocket Door Trim Kit is to make Pocket Door openings consistent with other Timely Frames on the project.Once layout is locked down, buy the straightest framing you can find and install it right away. Make sure you’ve read the pocket door hardware manufacturer’s instructions (we used a Johnson Hardware kit for double pocket doors). The manufacturer will provide measurements to get the rough-opening correct. Make sure your wall is straight and plumb, and most of all, that the head jamb is as level as possible—even if the floor isn"t. In fact, the floor in this project changed over an inch in the span of 60 inches. A key control point is clearance under the door. You want at least 3/4 inch for air to flow beneath the door.
best pocket doors
OK, let’s assume that none of those items is there, and you would like to install the door. A 32 inch door requires approximately 66 inches of linear space for the pocket door frame to be installed. The sheet rock will need to be removed, and more often than not, from both sides of the wall. The studs will also have to be removed so that a new door header can be installed. Depending upon the situation metal wrapped split studs may have to be installed to allow the new door to slide back and forth between them. Brackets will have to be installed. converging pocket door hardware
The Johnson Hardware 1500 Series Sliding Pocket Door Frame kit is an easily assembled, structurally strong pocket door frame designed for fast installation in standard 2 x 4 timber or steel-frame stud walls typically sheathed with drywall. Versatile frame can be adapted for use in thicker walls or cut down to accept any smaller size door. Features removable aluminum track with low-friction convex track rails; guaranteed jump-proof, smooth-rolling tricycle hangers; rust-resistant, zinc-plated, steel-reinforced, timber-split studs and self-adjusting floor anchors.
You can attach drywall to the frame, if you"d like, smooth and finish the wall and seams. Never use nails when installing a pocket door, as nails in the wall will impede the door’s flow. If you’ve purchased a door handle and lock for your pocket door, install the lock according to the instructions on the package. If you have an uncut doorframe, you will need to use a chisel to cut a depth for the locking mechanism. Follow the instructions on the package to do so.
How Do I Secure Electrical Wiring To A Pocket Door Frame?
The prefinished steel P-Series Pocket Door Trim Kit is used to trim out Pocket Door openings. The purpose of the P-Series Pocket Door Trim Kit is to make Pocket Door openings consistent with other Timely Frames on the project.johnson hardware pocket door
Once layout is locked down, buy the straightest framing you can find and install it right away. Make sure you’ve read the pocket door hardware manufacturer’s instructions (we used a Johnson Hardware kit for double pocket doors). The manufacturer will provide measurements to get the rough-opening correct. Make sure your wall is straight and plumb, and most of all, that the head jamb is as level as possible—even if the floor isn"t. In fact, the floor in this project changed over an inch in the span of 60 inches. A key control point is clearance under the door. You want at least 3/4 inch for air to flow beneath the door.
OK, let’s assume that none of those items is there, and you would like to install the door. A 32 inch door requires approximately 66 inches of linear space for the pocket door frame to be installed. The sheet rock will need to be removed, and more often than not, from both sides of the wall. The studs will also have to be removed so that a new door header can be installed. Depending upon the situation metal wrapped split studs may have to be installed to allow the new door to slide back and forth between them. Brackets will have to be installed.
how to find hardware
The Johnson Hardware 1500 Series Sliding Pocket Door Frame kit is an easily assembled, structurally strong pocket door frame designed for fast installation in standard 2 x 4 timber or steel-frame stud walls typically sheathed with drywall. Versatile frame can be adapted for use in thicker walls or cut down to accept any smaller size door. Features removable aluminum track with low-friction convex track rails; guaranteed jump-proof, smooth-rolling tricycle hangers; rust-resistant, zinc-plated, steel-reinforced, timber-split studs and self-adjusting floor anchors.
You can attach drywall to the frame, if you"d like, smooth and finish the wall and seams. Never use nails when installing a pocket door, as nails in the wall will impede the door’s flow. If you’ve purchased a door handle and lock for your pocket door, install the lock according to the instructions on the package. If you have an uncut doorframe, you will need to use a chisel to cut a depth for the locking mechanism. Follow the instructions on the package to do so.
